Stair Terminology Glossary of Terms

Click on the letters below to jump directly to that section of the Stair Terminology Glossary

A, B, C, D, E, F, G, H, I, K, L, M, N, P, Q, R, S, T, U, V, W

Below you will find a comprehensive list of stair terms and stair parts terminology, along with their definitions, for the commercial stair building industry.

Stair Terminology: Section A

ABRASIVE – Hard granular material of varying fineness, used in grinding and/or polishing, or embedded in metal to provide a nonslip surface. [NOMMA-86]

ALUMILITE – A trade name used by the Aluminum Company of America for its clear or color­impregnated anodized finishes in aluminum. [NOMMA-86]

ANCHOR – Any device used to secure a building component to adjoining construction or a supporting member. [NOMMA-86]

ANCHORAGE – Method of tying to adjoining construction or supporting member. [NOMMA-86]

ANGLED STAIR – (1) A stair in which successive flights are at an angle or other than 180 degrees. [NOMMA-86] (2) A stair in which successive flights are at an angle of other than 180 degrees to each other (often 90 degrees) with an intermediate platform. between them. [NAAMM-82]

ANNEAL – To heat above the critical or recrystallization temperature, then cool metal, glass or other materials, to eliminate the effects of cold working, relieve internal stresses or improve electrical, magnetic or other properties; to soften. [NOMMA-86]

ANODIC COATING – The surface finish resulting from anodizing. See Anodize. [NOMMA-86]

ANODIZE – To provide a hard non-corrosive oxide film on the surface of a metal, particularly aluminum, by electrolytic action in which the metal being treated serves as the anode. [NOMMA-86]

ARC WELDING – A process for the joining of metal parts by fusion, with the necessary heat being produced by an electric arc struck between an electrode and the metal or between two electrodes. [NOMMA-86]

AS FABRICATED – a) A term referring to the surface appearance and texture produced on metal mill products by the original forming process. b) A term referring to the surface appearance of a fabricated metal product before the removal of any disfigurations caused by the fabricating process. [NOMMA-86]

Back to Top

Stair Terminology: Section B

BALUSTER – One of a series of closely-spaced upright members which support the handrail in a railing. Also referred to as a Picket, Baluster Bar, Paling, Spacer Bar, etc. [NOMMA-86]

BALUSTRADE – A railing which is composed of balusters capped by a handrail, often serving as an architectural feature. [NOMMA-86]

BAR – A round, square, rectangular, hexagonal or similar section of rolled, drawn, or extruded metal. [NOMMA-86]

BAR SIZE SECTION – A hot rolled angle, channel, tee or zee having a greatest cross-sectional dimension less than 3 inches (76.2mm). [NOMMA-86]

BEND LINE – Point of change of direction of a structure. [NOMMA-86]

BEVEL (of stairs) – See Pitch (of stairs). [NOMMA-86]

BLOW HOLE – A hole or void in a casting, resulting from entrained gases. [NOMMA-86]

BONDERIZE – Chemical treatment of steel surface of another member, to strengthen and support it. (2) Chemical treatment of steel surface with proprietary phosphate solution, to provide limited, corrosion protection and improved paint base. [NOMMA-86]

BOTTOM RAIL – Lower member of railing system, supporting balusters or panels, if any. [NOMMA­86]

BRACKET – Projecting member attached to surface of another member, to strengthen and support it. [NOMMA-86]

BRAKING – Mechanical bending, flanging, folding and forming sheet or plate material, using press brake or folding brake. [NOMMA-86]

BRAZING – The joining of metal parts by heating them and, by capillary action, drawing a molten copper-zinc or other brazing alloy between them. [NOMMA-86]

BUFFING – The process of providing a lustrous finish by means of power-operated soft fabric wheels coated with a wax compound containing fine abrasive particles. [NOMMA-86]

BULLNOSE STEP – (1) Stair tread, usually first tread at flight bottom, with one or both ends having semi-circular or similar shape in plan view. [NOMMA-86] (2) A tread with one or both ends having a semi-circular shape in plan: usually the first tread at the bottom of member projecting beyond supports(s). [NAAMM-82]

BURNISHING – Developing smooth, lustrous surface of metal part by tumbling in drum containing small steel balls or by rubbing with hard pads. [NOMMA-86]

BUTT JOINTING – Fastening squared edge or end of one member to squared edge, end or face of another member without overlapping. [NOMMA-86]

Back to Top

Stair Terminology: Section C

CANTILEVER – Portion of member projecting beyond support(s). [NOMMA-86]

CAP – A fitting used to close the end of a pipe or tubular rail or post or the top end of a tubular newel. [NOMMA-86]

CAP RAIL – See Handrail. [NOMMA-86]

CARBON STEEL – Steel having either 1) no specified minimum content of alloying elements; 2) a specified minimum copper content not exceeding 0.40%, or 3) maximum specified percentage contents as follows: manganese 1.65, silicon 0.60, copper 0.60. [NOMMA-86]

CARBURIZING – Producing hard surface layer on steel by heating in carbonaceous medium and subsequent quenching to increase carbon content. Also referred to as “Case-Hardening.” [NOMMA-86]

CARRIER ANGLE – An angle connected to the inside face of a stair stringer to form a supporting ledge for the end of a tread or riser. Also referred to as Pitch Block. [NOMMA-86]

CARRIER BAR – A flat bar used in the same way as a carrier angle. [NOMMA-86]

CARRIERS – A term used for carrier angles or bars used to support treads formed from metal steps and gratings. [NOMMA-86]

CASE-HARDENING – See Carburizing. [NOMMA-86]

CASTING – A product formed by pouring molten metal into a mold. [NOMMA-86]

CAST IRON – A hard, brittle, non-malleable metal which can be produced in any shape. It cannot be hammered or bent. It is used for many miscellaneous metal products. Both functional and decorative, it has good resistance to corrosion. [NOMMA-86]

CAUSTIC DIPPING – Immersing metal in alkaline solution to chemically clean its surface. [NOMMA-­86]

CAUSTIC ETCH – A decorative matte texture produced on aluminum alloys by treatment in an alkaline solution, generally caustic soda (sodium hydroxide); also known as “frosted finish.” [NOMMA-86]

CEMENT, QUICK SETTING – Used in the installation of railing posts set in sleeves or holes. [NOMMA-86]

CHAMFER – To bevel a sharp edge. [NOMMA-86]

CHECKERED PLATE – See Floor Plate.

CIRCULAR STAIR – A stair which, in plan view, has an open circular form with a single center of curvature. See also Spiral Stair. [NOMMA-86]

CLIP – Small fastening device, usually of metal, to hold element or component in place by mechanical action or friction. [NOMMA-86]

CLOSURE BAR – A flat metal bar connected in the field to the top and/or bottom surface or edge of a wall stringer to close gaps between the stringer and the wall. [NAAMM-82]

COLD-FINISHED STEEL – Carbon steel which has been cleaned and pickled, then rolled or drawn through dies to produce a dimensionally accurate section with improved surface finish and often other improved properties. [NOMMA-86]

COLD ROLLING – Bringing metal sheet, plate or bar to final thickness and finishing by passing between heavy rollers without heating. [NOMMA-86]

COLLAR – See Escutcheon. [NOMMA-86]

COLUMN – A structural member which is subjected principally to axial compression loading. [NOMMA-86]

CONSTRUCTION JOINT – Discontinuity in structure. [NOMMA-86]

COPE – To cut away a portion of one member, either to form a close-fitting joint with, or provide clearance for, another member. [NOMMA-86]

CORROSION – The decay of metals, usually from oxidation. [NOMMA-86]

COR-TEN – The trade name used by the United States Steel Corporation for its weathering type of steel. See Weathering Steel. [NOMMA-86]

COUNTERBORING – Enlarging entrance of hole for placing bolt head or nut. [NOMMA-86]

COUNTERSINKING – Beveling end of hole for receiving conical head of flat- or oval-head fastener. [NOMMA-86]

COVER FLANGE – See Escutcheon. [NOMMA-86]

CURVED STAIR – A stair which, in plan view, has two or more centers of curvature, being oval, elliptical or some other compound curved form. [NOMMA-86]

Back to Top

Stair Terminology: Section D

DECKING – Light-gauge fluted, ribbed or cellular, sheet-metal platform for supporting floor or roof. [NOMMA-86]

DEFLECTION – (1) Bending or sagging deformation of member. [NOMMA-86] (2) A bending deformation of a structural member, usually within the elastic range of the material. [NAAMM­77]

DRAINAGE HOLE – See Vent Hole. [NOMMA-86]

DRAWING – The process of pulling metal in solid form through dies to alter its finish, mechanical properties or cross-sectional shape. [NOMMA-86]

DRAWINGS – Architectural and structural plan, often prepared by architect or engineer. They should  indicate by plan, elevation section and detail the location, quantity, size and extent of product to be furnished. [NOMMA-86]

DRAWINGS, SHOP – See Shop Drawings. [NOMMA-86]

DRIFT PIN – Tapered, round rod used to align holes in two or more pieces of metal. [NOMMA-86]

DROP (Stairs) – A fitting used to close the bottom end of a tubular newel. [NOMMA-86]

DURANODIC – Trade name used by the Aluminum Company of America for its hard anodic coatings. Se Hard Anodic Coating. [NOMMA-86]

Back to Top

Stair Terminology: Section E

EASEMENT (Stairs) – That curved portion of a handrail which forms a transition in a vertical plane, between a horizontal and an inclined section of the handrail. [NOMMA-86]

ELASTIC LIMIT – The maximum unit stress which can be applied to a material without causing permanent deformation. [NOMMA-86]

EMBED – To cast into concrete. [NOMMA-86]

EMBOSSED – Having a raised and/or indented pattern impressed on either one or both surfaces (of a sheet material) by means of patterned rolls or stamping dies. [NOMMA-86]

ESCUTCHEON – Protective or ornamental cover located usually at and around base of post or picket, baluster, or where a rail terminates against a wall. Also refereed to as Cover Flange, Collar, Wall Clip or Wall Flange. [NOMMA-86]

EXPANSION JOINT – A control joint designed to allow for differential movement of the joining parts due to thermal expansion and /or contraction, eliminating moment transfer. [NOMMA-86]

EXTRUSION – a) The process of producing metal shapes by forcing heated metal through an orifice in a die by means of a pressure ram. b) Any item made by this process. [NOMMA-86]

Back to Top

Stair Terminology: Section F

FABRICATE – To manufacture, form, assemble or construct metal products. [NOMMA-86]

FACE STRINGER – A stringer which supports, on one side, the ends of treads and risers, and is exposed on the other side. [NAAMM-77]

FACTOR OF SAFETY – The ratio of minimum yield stress or minimum ultimate stress to design or working stress. [NOMMA-86]

FASCIA – (1) a) In general, a horizontal band treatment on a wall, or the edge facing of a projecting element. b) In metal stairs, the exposed facing of the outer edge of a platform or floor; usually similar in detail to the face stringer. [NOMMA-86] (2) The exposed facing of the outer edge of a platform or floor; usually similar in detail to the face stringer. [NAAMM-821

FASCIA MOUNT – See Side Mount. [NOMMA-86]

FATIGUE – Structural failure of a material caused by repeated or fluctuating application of stress, none of which individually is sufficient to cause failure. [NOMMA-86]

FERROUS METAL – Metal in which iron is the principal element. [NOMMA-861

FIELD CHECK – Verification of existing dimensions against those shown on drawing prior to fabrication. [NOMMA-86]

FIELD JOINT – A connection between two adjoining members or parts, made at the time of installation, generally accomplished by use of an internal mechanical connector or by welding. [NAAMM­-77]

FIELD MEASURE – Survey of existing conditions. [NOMMA-86]

FILL (Stairs) – A cementitious material, such as concrete or terrazzo, which is placed over a metal substructure to provide the wearing surface of a tread or platform. [NOMMA-86]

FINIAL – An ornamental piece on top of railing post, newel or fence. Also referred to as Urn. [NOMMA-86]

FIXED METAL STAIR – A permanently stationary series of three or more steps in one or more flights, providing pedestrian access between different floors or levels. [NAAMM-82]

FLAT – Rectangular bar of width greater than its thickness. [NOMMA-86]

FLIGHT – An uninterrupted series of steps. [NOMMA-86]

FLIGHT HEADER – See Header, Flight. [NOMMA-86]

FLIGHT RISE – The vertical distance between the floors or platforms connected by a flight of stairs. [NOMMA-86]

FLIGHT RUN – The horizontal distance between the faces of the first and last risers in a flight. [NOMMA-86]

FLOOR PLATE – Steel plate having a raised pattern to provide a non-slip wearing surface; referred to as “tread plate” when made of aluminum. [NOMMA-86]

FLUSH BOLT – A rod or bolt which is mounted flush with the edge or face of the inactive door of a pair, to lock the door to the frame at the head and/or still. When mounted in the edge, operation is by means of a recessed lever. [NOMMA-86]

FLUSH FITTING – A pipe or tube fitting having the same outside diameter as the pipe or tube to which it is joined. [NAAMM-77]

FORGING – Heating and hammering metal into a desired shape. [NOMMA-86]

FORMING – The process of shaping metal by mechanical action other than machining, forging, or casting. [NOMMA-86]

Stair Terminology: Section G

GAGE – See Gauge [NOMMA-86]

GALVANIC CORROSION – The electrochemical action which takes place when dissimilar metals are in contact in the presence of an electrolyte, with the extent of corrosion being governed by both the difference in potential between the two metals and the relative areas of the metal parts. [NOMMA-86]

GALVANIZING – The process of coating metal with zinc, either by dipping in a bath of molten zinc, by mechanical coating or electrolytic action. [NOMMA-86]

GAUGE – a) A number indicating the thickness of metal or the diameter of a wire or a fastener shank, in accordance with a standard series of numbers, each of which represents a certain decimal fraction of an inch (or number of millimeters). b) The distance, in inches, between adjacent lines of holes or fasteners. [NOMMA-86]

GENUINE WROUGHT IRON – Low carbon content used for finer types of decorative iron works where resistance to corrosion is of value. Suppliers are somewhat limited. When Genuine Wrought Iron is specified, the words “wrought iron” are not sufficient, and this term may denote any carbon steel. Therefore, in specifying, it is important that the words “Genuine Wrought Iron” be used. Also see Wrought Iron.” [NOMMA-86]

GRAB RAIL (Grab Bar) – A short length of rail located for safety and convenience. [NOMMA-86]

GRINDING – Removing metal from a surface by means of abrasive action. [NOMMA-86]

GRIT – Granular abrasive material such as aluminum oxide or silicon carbide, which may be coated on cloth, paper or wheels for sanding grinding or polishing purposes. Also used as surface roughener for metal to provide non-slip surface. [NOMMA-86]

GRIT NUMBER – The grain size of an abrasive used for grinding or polishing metal. Also, the degree of fineness of a metal finish produced by that abrasive. Grit numbers are in an ascending order from coarse to fine. [NOMMA-86]

GUARDRAIL SYSTEM – Rail system usually located for protection of building occupants at or near outer edge of stair, ramp, landing, platform, balcony or accessible roof; at perimeter of any opening or accessible surface, such as opening for stairway; or at location where operating condition requires limitation of access to designated area to guard against accidental falls or injury. See Railing System. [NOMMA-86]

GUSSET – A piece of metal plate used to construct or reinforce a line or angular joint between two or more metal members. [NOMMA-86]

Back to Top

Stair Terminology: Section H

HAMMERING – Hot or cold, machine or hand peening or denting of metal surfaces for artistic effect. Also referred to as Swedish Look. [NOMMA-86]

HAND OF SPIRAL STAIR – A term used to designate the tuna direction of a stair. Right-hand refers to a stair on which the user turns counter-clockwise as he ascends. Left-hand refers to a stair on which the user turns clockwise as he ascends. [NOMMA-86]

HANDRAIL – Horizontal or sloping member normally grasped by hand. This member may be part of a railing system and often, but not necessarily, top member (top rail); or may be mounted on wall or other building element. When part of stair-rail system, it is a member paralleling the pitch of the flight and is often, but not necessarily, top member. See Wall Handrail. [NOMMA-86]

HANGER (Stairs) – A load-carrying tension member used to support a stair framing member by suspension from floor construction or other support above. [NOMMA-86]

HARD ANODIC COATING – A coating on aluminum by a proprietary anodizing process, without the use of dyes or pigments. It provides a high resistance to abrasion and corrosion and is produced in various shades of bronze and gray, as well as black. [NOMMA-86]

HEADER, FLIGHT – A horizontal structural member used in stair construction at a floor or platform level to support the end(s) of one or more stringers. [NOMMA-86]

HEADER, PLATFORM – A horizontal structural member supporting stair platform construction but carrying no stringers. [NOMMA-86]

HEADING – The process of “upsetting” or enlarging the end of a piece of metal. [NOMMA-86]

HEADROOM – The minimum vertical distance from the top surface of a stair tread or platform to the ceiling, soffit or other overhead obstruction, measured at the outer edge of a tread. [NOMMA-­86]

HIGH-STRENGTH LOW-ALLOY STEEL – Steel having a chemical composition specifically developed to impart higher mechanical property values and, in some cases, greater resistance to atmospheric corrosion than is obtainable from conventional carbon structural steels. [NOMMA-86]

HOT DIP GALVANIZING – The process or result of applying a protective coating to ferrous metal by dipping in a bath of molten zinc. [NOMMA-86]

HOT ROLLED – Shaped by passing a heated billet between rollers. [NOMMA-86]

HOT WORKING – The process of forming a metal when its temperature is higher than its recrystallization temperature. [NOMMA-86]

HANDRAIL BRACKET – (1) A device attached to a wall, post or other surface to support a handrail. [NOMMA-86] (2) A device attached to a wall, post or other surface to support a handrail. A left-hand handrail bracket is one which is located on the users left as he ascends the stairs. A right-hand handrail bracket is one which is located on the user’s right as he ascends the stairs. [NAAMM-77]

Back to Top

Stair Terminology: Section I

I.P.S. – Iron pipe size; the nominal inside-diameter dimension of pipe. [NOMMA-86]

Back to Top

Stair Terminology: Section K

KALCOLOR – The trade name used by Kaiser Aluminum and Chemical Corporation for its hard anodic coatings. See Hard Anodic Coating. [NOMMA-86]

KICK PLATE – a) A protective plate fastened to the lower face or faces of a door. b) A vertical plate forming a lip or low curb at the open edge of a stair platform or floor, or at the back edge or open end of a stair tread, on an open riser stair. Also referred to as Toe Plate, Toe Board. [NOMMA-86]

KNOB – An ornamental curved and tapered fitting terminating a handrail. [NOMMA-86]

KNOCKED DOWN – A term used in reference to any product that is shipped disassembled, for assembly at the building site; commonly abbreviated “KD.” [NOMMA-86]

Back to Top

Stair Terminology: Section L

LAMB’S TONGUE – An ornamental curved and tapered fitting terminating a handrail. [NOMMA-86]

LANDING – Level part of staircase at end of stair flight. See Platform. [NOMMA-86]

LAP SEAM – Joint formed by overlapping edges of metal sheets or plates and joining them by riveting, welding, soldering, or brazing. [NOMMA-86]

LAY OUT – To scale out configuration of structure. [NOMMA-86]

LATERAL SCROLL – A fitting which curves in a horizontal plane, used to terminate a stair handrail. Often ends up as a round plate covering the top of a post. [NOMMA-86]

LINTEL – A horizontal structural member spanning a wall opening at its head to support the wall above the opening. [NOMMA-86]

Back to Top

Stair Terminology: Section M

MALLEABLE IRON – A sand cast iron which is annealed and can be bent cold to some degree. It is used in many metal building products where strength and ability to resist shock are essential. It is easily welded without danger of cracking by the same method used for welding steel. [NOMMA-86]

MAYARI-R STEEL – Trade name used by Bethlehem Steel Corporation for its type of Weathering Steel. See Weathering Steel. [NOMMA-86]

MECHANICAL COATING – The process of applying a protective coating to ferrous metal by hammering zinc powder or flakes into metal surface with glass pellets during tumbling. [NOMMA-86]

MECHANICAL CONNECTIONS – A connection between railing members made by means other than welding or adhesive bonding. [NAAMM-77]

MECHANICAL PROPERTIES – Properties characterizing response to applied forces, such as strength, stiffness, elasticity and ductility. [NOMMA-86]

METALLIZE – To apply a coating of metal, usually in a powdered or molten form, on a base metal or other material. [NOMMA-86]

MID RAIL – Rail located between top and bottom rails. [NOMMA-86]

MILL FINISH – The original surface finish produced on a metal mill product by rolling, extruding, or drawing. [NOMMA-86]

MILL SCALE – The scaly oxidized surface produced on steel by heating and hot rolling. [NOMMA-86]

MOCKUP – A section of a structure or assembly, built full size or to scale, for purposes of testing its performance, studying its construction details or judging its appearance. [NOMMA-86]

MOLD – A form into which molten metal is poured to produce a casting. [NOMMA-86]

Back to Top

Stair Terminology: Section N

NEWEL – A post member, usually square or rectangular in cross section, supporting the end of a stair railing or serving as a common support for two stair railings. [NOMMA-86]

NON-FERROUS – Metal without any iron content. [NOMMA-86]

NOSING – That part of a stair tread or platform which projects as a square, rounded or rounded and molded edge beyond the vertical face of the riser below it. [NOMMA-86]

Back to Top

Stair Terminology: Section P

PAN BRACKET (Stairs) – See Carrier Angle or Carrier Bar. [NOMMA-86]

PAN TREAD (Stairs) – See Tread, Pan Type. [NOMMA-86]

PANEL – Portion of railing between posts, top rail and bottom rail. [NOMMA-86]

PARALLEL STAIR – A stair consisting of flights which parallel each other and are separated only by one or more intermediate platforms. [NOMMA-86]

PATTERN – Model for making mold into which molten material is poured to produce casting; to reproduce like image in mold. [NOMMA-86]

PERFORATING – Punching or drilling an overall pattern of holes or openings in sheet metal. [NOMMA-86]

PERFORMANCE – Conformance with established criteria. [NOMMA-86]

PERMANENT – Functioning indefinitely without fundamental or marked change; in contrast to temporary. [NOMMA-86]

PERMANENT SET – The extent to which a component or structure is permanently deformed by an applied load after removal of the load. [NOMMA-86]

PHOSPHATIZING – The process of producing a phosphate conversion coating on metal by dipping it in a suitable aqueous solution of phosphoric acid, to improve paint adhesion and increase corrosion resistance. [NOMMA-86]

PHYSICAL PROPERTIES – Material properties, such as specific gravity or density, electrical and thermal conductivity, and coefficient of thermal expansion, serving to characterize and to distinguish between different kinds of matter. [NOMMA-86]

PICKET – One of a series of closely-spaced upright members which support the handrail in a railing. See baluster. [NOMMA-86]

PICKET CASTING – Ornamental design attached to a picket. [NOMMA-86]

PICKET RAILING – Railing consisting of posts, pickets, top rail and, sometimes, bottom rail. [NOMMA-86]

PICKLING – The treatment of metal surfaces with a strong oxidizing agent, such as nitric acid, to make them chemically clean and provide a strong, inert oxide film. [NOMMA-86]

PIPE RAILING – Railing fabricated of pipe. [NOMMA-86]

PIPE, ROUND – A hollow round section of metal, the size of which is usually designated by nominal inside diameter in inches (or millimeters). [NOMMA-86]

PITCH – The inclination or slope, measured either in degrees, percent, or by the ratio of rise to run. [NOMMA-86]

PITCH BLOCK – See Carrier Angle. [NOMMA-86]

PITCH DIMENSION (Stairs) – The distance between the bases of the top and bottom risers in a flight, measured parallel to the slope. Sometimes referred to as the nose to nose dimension. [NOMMA-86]

PITTING – Localized surface defects on metal, in the form of small depressions or ‘pits’, usually caused by electrochemical corrosion. [NOMMA-86]

PLATE – Flat Metal .180″ or over in thickness and over 8″ in width. [NOMMA-86]

PLATFORM (Stairs) – A horizontal surface having a dimension parallel to the stringer greater than a tread width and occurring in a stair at the end of a flight or between flights, either at a floor level or between floors. In the latter case, it is sometimes referred to as an intermediate platform or landing. [NOMMA-86]

PLATFORM HEADER – See Header, Platform. [NOMMA-86]

POCKET – Opening provided in structure to accept post, rail-supporting bracket or structural member. [NOMMA-86]

POST (Railing) – A vertical, supporting member of a railing system. [NOMMA-86]

PRE-ASSEMBLED STAIR – A stair whose components are assembled in the plant to make up units of varying sizes and degrees of complexity. [NAAMM-82]

PRE-ERECTED STAIR – A stair unit for multi-storied buildings designed to be self supporting. Such units can be stacked one upon the other and field connected to form stair towers. [NAAMM-82]

PRIMER – Liquid coating applied to surface prior to application of paint or other finish. [NOMMA-86]

PRIMER PAINT – First coat applied to metal to retard corrosion temporarily and to provide satisfactory adhesion of finish coat. [NOMMA-86]

PUNCHING – A process of forcing a punch through the metal into a die, forming a hole in the shape of the punch. [NOMMA-86]

Back to Top

Stair Terminology: Section Q

QUENCHING – The process of cooling heated metal by contact with a liquid, gas or solid, for purposes of hardening or tempering. [NOMMA-86]

Back to Top

Stair Terminology: Section R

RAIL – Horizontal, vertical or inclined member of railing system. See Railing System, Handrail, Wall Handrail, Stair Rail System. [NOMMA-86]

RAILING – See Railing System. [NOMMA-86]

RAILING SYSTEM – A framework of horizontal, vertical or inclined members or panels, or some combination of these, supporting a handrail and located at the edge of a stair flight platform or floor, as a safety barrier. See Guard Rail System and Stair Rail System. [NOMMA-86]

RAKE – See Pitch. [NOMMA-86]

RAKE DIMENSION – See Pitch Dimension. [NOMMA-86]

RAMP RAIL, SYSTEM – A railing system located along side(s) of ramp. [NOMMA-86]

RESIDUAL DEFLECTION – See Permanent Set. [NOMMA-86]

RETURN – A rail bend of 180°, as at a stair platform or railing terminal. See also Wall Return. [NAAMM-77]

RISE – See Flight Rise. [NOMMA-86]

RISER – The vertical or inclined face of a step, extending from the back edge of one tread to the outer edge of the tread or lower edge of the nosing next above it. [NOMMA-86]

RISER, OPEN – A term used to describe a stair having open spaces rather than risers between treads. [NOMMA-86]

RISER FIGHT -The vertical distance between the top surfaces of two successive treads. [NOMMA­-86]

RUN – See Flight Run and Tread Run. [NOMMA-86]

Back to Top

Stair Terminology: Section S

SADDLE – See threshold. [NOMMA-86]

SAFETY NOSING – A stair nosing having an abrasive nonslip surface flush with the tread surface. [NOMMA-86]

SAFETY TREAD – A stair tread which is covered on its top surface with an abrasive or nonslip material. [NOMMA-86]

SAND BLASTING – Subjecting to a stream of sand projected at high velocity under air or steam pressure, for the purpose of removing scale or encrusted material or to provide a textured finish. [NOMMA-86]

SANITARY COVE (Stairs) – A small projection formed in the face of a metal riser along its full length to provide an angled or curved transition between the tread surface and the riser face, to facilitate cleaning. [NOMMA-86]

SCISSOR STAIR – A straight stair which in plan view has two parallel flights between floors but in which the stairs are at a 180 degree angle to each other. [NAAMM-82]

SCREEN – Perforated panel or wire mesh serving as a panel. [NOMMA-86]

SCROLL – Ornamental spiral or convoluted form serving, e.g., as decorative railing panel or insert, either cast or forged. [NOMMA-86]

SHEET – Thin, flat, rolled metal product having mill or cut edges, less than .229″ in thickness. [NOMMA-86]

SKIP’S LADDER – A ship’s ladder is named for its use as a stairway access between decks of a ship. These ladders ascend at steep angles of not less than 50 degrees nor more than 77 degrees with the deck, and cover the angularity of ascent between that of conventional stairs and straight ladders they are not used for public stairways in buildings. [NAAMM-82]

SHOP DRAWING – A working drawing usually prepared the fabricator. [NOMMA-86]

SIDE MOUNT – (1) Railing support anchoring post to vertical surface, such as fascia or stringer face. [NOMMA-86] (2) A method of railing support in which the posts are anchored to a vertical surface such as a fascia or stringer face. Also referred to as fascia bracket of fascia flange. [NAAMM-77]

SLAG – The crusty residue resulting form melting or welding metal. [NOMMA-86]

SLEEVE – a) A tubular section of sheet metal or other material placed in concrete or masonry to provide either a pocket or opening for the insertion or the penetration of another item. b) An internal tubular splice between abutting sections of pipe, tubing, or tube-like members. [NOMMA-86]

SLIP JOINT – A joint which permits relative sliding movements of the joining parts. [NOMMA-86]

SLOPE – See pitch. [NOMMA-86]

SOFFIT (Stairs) – (1) Underside of stair in exposed construction. Also, finish material applied to underside of stair. [NOMMA-86] (2) The under side of a stair, whether exposed construction or an applied finish material. [NAAMM]

SPECIFICATIONS – Document providing descriptive or performance requirements and criteria. [NOMMA-86]

SPINDLE – A tapered round picket, with center part larger in diameter than ends. [NOMMA-86]

SPIRAL STAIR – A stair with a closed circular form, uniform sector-shaped treads and a supporting center column. [NOMMA-86]

SPIRAL STAIR, LIMITED ACCESS – A spiral stair serving an occupant load of 10 or less and from an area of 600 square feet or less. [NAAMM]

SPIRAL STAIR, PRIMARY ACCESS – A spiral stair serving an occupant load of 50 or less. [NAAMM]

SPLICE PLATE – A plate used for fastening two or more members together. [NOMMA-86]

SPRAYING – The process of coating metal with paint, another metal or any other material by use of air or hydraulic pressure. [NOMMA-86]

SQUARES – A term used in reference to square metal bars having either slightly rounded or sharp corners. [NOMMA-86]

STAIR – (I) A flight or series of connecting flights extending between two or more floors. [NOMMA­86] (2) A flight or series of connected flights extending between two or more levels within a given floor area or stair well. [NAAMM-77]

STAIR LIFT – See Flight. [NOMMA-86]

STAIR-RAIL SYSTEM – Railing system located along open sides of stair and landing. [NOMMA-86]

STAIR-RUN – One run of stairs between floors, platforms or floors and platforms. [NOMMA-86]

STAIRWAY – See Stair. [NOMMA-86]

STAIR-WELL – The vertical shaft space in a building occupied by a stair; also, the open well space between a series of flights. [NOMMA-86]

STEP – The combination of a riser and the tread immediately above it. [NOMMA-86]

STEP RISE – See Riser Height. [NAAMM-82]

STIFFENER – A reinforcing member which serves to prevent or limit the deformation of the member to which it is attached. [NOMMA-86]

STORY HEIGHT – The vertical distance, in a building, between one finished floor and the next.

STRAIGHT RUN STAIR – Stair extending in straight line between two floors and consisting of single flight or series of flights with one or more intermediate platforms. [NOMMA-86]

STRING – See Stringer, the preferred term. [NOMMA-86]

STRINGER (Stair) – An inclined structural member supporting a flight of stairs, or a structural member having an inclined section with a horizontal section at one or both ends, supporting a flight and one or two platforms. [NOMMA-86]

STRINGER, BOXED – A stringer having a hollow square or rectangular cross section. [NOMMA-86]

STRINGER, CENTER – A stringer located under a flight at its mid-width and supporting the treads, or treads and risers. [NOMMA-86]

STRINGER, CLOSED See Stringer, Boxed. [NOMMA-86]

STRINGER, FACE – A stringer which supports, on one side, the ends of treads and risers, and is exposed on the other side. [NOMMA-86]

STRINGER, OPEN – A structural channel used as a stringer. [NOMMA-86]

STRINGER, PLATE – A flat plate used as a stringer. [NOMMA-86]

STRINGER, PLATFORM – A stringer, or that part of a stringer, which is used to support a platform. [NOMMA-86]

STRINGER, TUBE – A stringer made from a metal tube section. [NOMMA-86]

STRINGER, WALL – A stringer placed alongside a wall, and usually carrying no railing. [NOMMA-­86]

STRIP – Flat metal, .229″ or less in thickness and 12″ or less in width. [NOMMA-86]

STRUT – (1) A vertical compression member designed to resist axial loads. [NOMMA-86] (2) A structural member which resists axial compression loads. Generally used to support a stair framing member by column action. [NAAMM-82]

SUB-PLATFORM – The metal subfloor over which a fill is placed to provide a platform. [NAAMM-­82]

SUB-TREAD – See Tread, Pan Type. [NOMMA-86]

SWEDISH IRON LOOK – See Hammering. [NOMMA-86]

Back to Top

Stair Terminology: Section T

TACK WELD – a) A small temporary weld applied to metal parts to hold them in correct position while completing an assembly. b) One of a series of small welds applied where a continuous weld is unnecessary. [NOMMA-86]

TEMPERING – Heating metal, glass or other material to temperature below transformation stage, subsequently cooling it at controlled rate to change its hardness, strength, toughness or other property. [NOMMA-86]

TEMPLATE – a) A pattern used as a guide in fabricating a part. b) A precise detailed layout or pattern for providing the necessary fabrication details. [NOMMA-86]

TENSILE STRENGTH – The maximum load which can be sustained by metal in tension measured in pounds per square inch. [NOMMA-86]

THRESHOLD – A raised member extending between the jambs of a door frame at the floor. [NOMMA-86]

TOE BOARD – See Kick Plate. [NOMMA-86]

TOE PLATE – See Kick Plate. [NOMMA-86]

TOLERANCE – Permissible deviation from a nominal or specified dimension or value. [NOMMA-86]

TOP RAIL – The top member of a rail system, sometimes called cap rail. [NOMMA-86]

TRAFFIC RAH, SYSTEM – A railing system designed for the control of movement of people, requiring special consideration for given end-use conditions. [NOMMA-86]

TRANSFER RAIL SYSTEM – Railing system designed for transfer of body weight in such locations as toilets, showers and tub enclosures. [NOMMA-86]

TRAVEL AREA – That area with which -a stair user might normally make physical contact. [NAAMM]

TREAD – The horizontal member of a step. [NOMMA-86]

TREAD ANGLE – Se Carrier Angle. [NAAMM]

TREAD BAR – See Carrier Bar. [NAAMM]

TREAD DEPTH – The tread run plus the projection of the nosing, if any. NOMMA-86]

TREAD, GRATING TYPE – Tread fabricated from metal grating. [NOMMA-86]

TREAD LENGTH – The dimension of a tread measured perpendicular to the normal line of travel on a stair. [NOMMA-86]

TREAD PAN – A section formed from sheet metal to receive a fill and provide, when filled, either a tread or combination tread and riser. [NOMMA-86]

TREAD, PLATE TYPE – A tread, or a combination of tread and riser, fabricated from metal plate, floor plate, tread plate or a combination of plates. [NOMMA-86]

TREAD RUN – The horizontal distance between two consecutive risers or, on an open riser stair, the horizontal distance between nosings or the outer edges of successive treads, all measured perpendicular to the front edges of the nosings or treads. [NOMMA-86]

TREAD WIDTH – The tread run plus the projection of the nosing, if any. [NAAMM-82]

TUBING – A hollow section of metal having a round, square, rectangular or other cross-sectional form. Size is designated by outside dimension(s) in inches or millimeters, and wall thickness in gauge number, thousandths of an inch, or millimeters, or fraction of an inch. [NOMMA-86]

Back to Top

Stair Terminology: Section U

UPSETTING – A cold, or hot-forging operation by which the cross-sectional area of a bar of rod in increased locally. [NOMMA-86]

URNS – See Finials. [NOMMA-86]

Back to Top

Stair Terminology: Section V

VENT HOLE – Opening for escape of gas or liquid or for relief of pressure, especially required in fabricating when item is to be coated by immersion or hot-dip galvanized. Also referred to as drainage hole. [NOMMA-86]

VERTICAL BARRIER – A wall or railing adjacent or attached to the edge of a flight, platform or floor, to prevent persons from falling. [NAAMM-82]

VOLUTE (Stairs) – A spiral or scroll-shaped fitting used to terminate a stair handrail. [NOMMA-86]

Back to Top

Stair Terminology: Section W

WALL CLIP OR WALL FLANGE – A bracket used for anchoring. [NOMMA-86]

WALL HANDRAIL – Handrail attached to wall adjacent to stair and paralleling pitch of flight, also used along walkway, ramps and corridors. Also referred to as a Wall Rail. [NOMMA-86]

WALL RAIL – See Wall Handrail [NOMMA-86]

WALL RETURN – A bend at the end of a wall handrail, turning it toward the wall to which it is attached. [NOMMA-86]

WEATHERING STEEL – High-strength, low alloy steel made especially for application requiring light weight, high strength and resistance to corrosion of approximately 5 to 6 times that of low­carbon steel. [NOMMA-86]

WEEPHOLE – A small opening provided to permit the drainage of fluid. [NOMMA-86]

WELDING – The process of joining two metals or alloys by fusion. [NOMMA-86]

WELDING ROD – Metal rod of suitable composition to be used as a source of filler material in arc or gas welding. [NOMMA-86]

WINDER – A tread having less width at one end than at the other. [NOMMA-86]

WIRE MESH – See Screen. [NOMMA-86]

WORKING DRAWING – See Shop Drawing. [NOMMA-86]

WROUGHT IRON – (1) Fabricated ornamental work, usually made of mild steel of commercial quality. Also see Genuine Wrought Iron. [NOMMA-86] (2) A ferrous material, aggregated from a solidifying mass of pasty particles of highly refined metallic iron, with which, without subsequent fusion, is incorporated a minutely and uniformly distributed quantity of slag. [ASTON]

REFERENCES

Aston, James and Edward B. Story. WROUGHT IRON, Its Manufacture, Characteristics and Applications. Pittsburgh, Pennsylvania: A. M. Byers Company, 1939.

National Association of Architectural Metal Manufactures (NAAMM).

METAL STAIRS MANUAL. 1982. Fourth Edition.
National Association of Architectural Metal Manufactures (NAAMM). PIPE

RAILING MANUAL: Including Round Tube. 1977.
National Ornamental & Miscellaneous Metals Association (NOMMA).

METAL RAIL MANUAL. A Guide for Architects, Designers, Fabricators, and Installers. 1986. Second Edition.

Back to Top