Electronic Payments

Unistrut Buffalo Supports

Kee Lite Safety Railing Systems

A simple, effective solution for added safety

Aluminum Safety Components provide a lightweight, corrosion resistant, and strong alternative for flexible fabrication of pipe railings and structures. Aluminum components can be used for a variety of applications from contemporary to industrial.

Kee Safeyy systems provide simple, modular solutions that are cost effective, flexible and efficient to install.

View More
L14-Kee-Lite-Straight-Coupling.jpg
No. L14 Straight Coupling
Designed to give an in-line joint between tubes of the same size. Frequently used to allow full pipes to be used in railing applications.
 
Note: It is not advisable to join the upper and lower rails of a railing within the same bay.
More Info
---
Choose Options
View More
L19-Kee-Lite-Adjustable-Side-Outlet-Tee.jpg
No. L19 Adjustable Side Outlet Tee
Used to form variable angle joints between 60 and 200 degrees. These fittings are not designed to absorb bending loads at barrel intersection.
 
Note: Type L19 fittings are bagged in pairs and are weighed, priced, and sold as such.
More Info
---
Choose Options
View More
L29-Kee-Lite-30-Degree-To-60-Degree-Single-Socket-Tee.jpg
No. L29 30 Degree to 60 Degree Single Socket Tee

This adjustable fitting is most frequently used for struts and braces. It can be used at any selected angle between 30° and 60°. Suitable for connecting an angled staircase rail to a vertical upright.

More Info
---
Choose Options
View More
L30-Kee-Lite-35-Degree-To-45-Degree-Adjustable-Cross.jpg
No. L30 30 Degree to 45 Degree Adjustable Cross

This adjustable fitting can be used for railing on staircases between the mid-rail and intermediate upright which is required to remain vertical. It can be used at any selected angle between 30° and 45°.

More Info
---
Choose Options
View More
L35-Kee-Lite-Three-Socket-Cross.jpg
No. L35 Three Socket Cross

Most frequently used to tie uprights with horizontal pipe in three directions, all at 90 degrees to the upright. The upright passes through the fitting.

More Info
$25.64
Buy
View More
L46-Kee-Lite-Combination-Socket-Tee-And-Crossover.jpg
No. L46 Combination Socket Tee and Crossover

Used on racking to join horizontal carrying rails to the upright, leaving the socket to take a horizontal tie across the section. For shelved racking, it is usual to have the horizontal pipe outside the upright. On pallet racking, it is preferable to have the carrying rails inside the upright.

More Info
$23.70
Buy
View More
LC50-Kee-Lite-Single-Swivel-Socket.jpg
No. LC50 Single Swivel Socket
Complete combination fitting.
 
Note: Swivel fittings are not designed to resist bending loads. A structure should not be designed entirely of swivel fittings as they will not provide sufficient stability for the structure.
More Info
---
Choose Options
View More
LF50-Kee-Lite-Female-Single-Swivel-Socket-Member.jpg
No. LF50 Female Single Swivel Socket Member

The female part of a swivel fitting combination. Ø indicates diameter of rivet holes. 

More Info
---
Choose Options
View More
LM50-Kee-Lite-Male-Single-Swivel-Socket-Member.jpg
No. LM50 Male Single Swivel Socket Member

The male part of a swivel fitting combination. The fitting can also be used to attach flat panels to tubular structures. Ø indicates diameter of rivet hole.

More Info
---
Choose Options
View More
LM51-Kee-Lite-Male-Double-Swivel-Socket-Member.jpg
No. LM51 Male Double Swivel Socket Member

One half of a combination fitting. This can also be used for attaching flat panels to tubular structures. Ø indicates diameter of rivet hole.

More Info
---
Choose Options
View More
LC51-Kee-Lite-Double-Swivel-Socket.jpg
No. LC51 Double Swivel Socket

Complete combination fitting. Reducing combinations of Type LC51 are available, Sizes 6, 7 and 8.

More Info
---
Choose Options
View More
LM52-Kee-Lite-Male-Corner-Swivel-Socket-Member.jpg
No. LM52 Male Corner Swivel Socket Member

One half of a combination fitting. This can also be used for attaching flat panels to tubular structures. Ø indicates diameter of rivet hole.

More Info
---
Choose Options
View More
LB54-Kee-Lite-Adjustable-Elbow.jpg
No. LB54 Adjustable Elbow

A swivel fitting designed as an in-line variable angle connection, adjustable from 45° to 200°.

More Info
---
Choose Options
View More
LM58-Kee-Lite-Male-Wall-Plate.jpg
No. LM58 Male Wall Plate

The male part of a swivel fitting for attaching angled tubing to flat surfaces. Ø indicates diameter of rivet holes.

More Info
$11.17
Buy
View More
LC58-Kee-Lite-Swivel-Flange.jpg
No. LC58 Swivel Flange
A swivel fitting for attachment of angled pipe to a flat setting. Ø indicates diameter of rivet hole.
 
Note: This fitting is not recommended for use as a base flange to support guardrail or balustrades.
More Info
---
Choose Options
View More
L61-Kee-Lite-Flange.jpg
No. L61 Flange
This flange, with holes provided for countersunk head fixing screws only, is used on structures where the fixing required is positional only. Frequently used as a wall-fixing bracket. Ø indicates diameter of fixing holes.
 
It is not recommended for use as a base flange to support guardrail or balustrades
More Info
---
Choose Options
View More
L62-Kee-Lite-Standard-Railing-Flange.jpg
No. L62 Standard Railing Flange

Ideal when a structural fixing is required. Type L62 should always be used to fix down guardrailing and balustrades. The holes are of sufficient diameter to give a good fixing with either a mechanical or chemical anchor, and the two socket set screws in the vertical socket give greater stability to the upright. It is recommended that the fixing holes in the flanges should be inline with the applied load. Ø indicates diameter of fixing holes.

More Info
---
Choose Options
View More
L68-Kee-Lite-Wall-Flange.jpg
No. L68 Wall Flange
Side palm fixing for guardrailing and balustrading to walls, parapets, steps and ramps. The upright cannot drop throught the socket. Ø indicates diameter of fixing holes.
 
Note: If the upright is required to pass through the fitting by machining out the base stop, the bottom fixing hole becomes unusable.
More Info
---
Choose Options
View More
L69-Kee-Lite-Railing-Flange.jpg
No. L69 Railing Flange with Toeboard Adapter

The Type L69 fitting has been designed for guardrailing and balustrading applications and provides the added benefit of attaching a kick plate to the base. The base plate holes are of sufficient diameter to allow for attachment with either a mechanical or chemical anchor, the side plates have slotted holes to allow for a degree of sideways movement for ease of installation. Ø indicates diameter of fixing holes.

More Info
---
Choose Options
View More
L70-Kee-Lite-Rail-Support.jpg
No. L70 Rail Support
This fitting, with holes provided for countersunk flat head screw fixings only, is designed to carry handrails along walls or to fix structures back to walls. The pipe passes through the fitting and cannot be joined within the fitting. Type 70 is also used to attach toeboards to the bases of guardrail uprights. Ø indicates diameter of fixing holes.
 
WARNING!: Type 70 fittings are not designed to be used as base flanges for full height guardrails or handrails
More Info
---
Choose Options
View More
L84-Kee-Lite-Malleable-Plug.jpg
No. L84 Malleable Plug
A metal drive-in plug, which is difficult to remove after installation. For proper insertion, a rubber mallet should be used
More Info
Call for price
Buy
View More
L150-Kee-Lite-Heavy-Duty-4-Hole-Square-Flange.jpg
No. L150 Heavy Duty 4 Hole Square Flange
A heavy duty, four point fixing, base flange. Ideal when a structural fixing is required. Ø indicates diameter of fixing holes.
More Info
$37.50
Buy
View More
L160-Kee-Lite-Smooth-Handrail-Fitting.jpg
No. L160 Smooth Handrail Fitting

Designed to provide attachment for a smooth handrail. The fitting swivels allowing the handrail to be placed at any angle. The fitting is supplied as a kit including fasteners. Ref ‘A’ refers to the diameter of the post.

More Info
---
Choose Options
View More
L164-Kee-Lite-Offset-Wall-Flange.jpg
No. L164 Offset Wall Flange

This fitting is designed for side palm fixing of uprights to stell channels, walls, parapets, steps and ramps. The upright cannont drop through the socket. Ø indicates diameter of fixing holes.

More Info
$55.99
Buy