Unistrut Buffalo: Distributers of the Lindapter System

Electronic Payments

Eberl Iron

Lindapter Structural Fastening System

Lindapter products are used to connect structural steel on both permanent and temporary structures worldwide. The exclusive and patented connections are independently approved by respected international associations with Lindapter’s load bearing capacities tested and verified. Third party recognition also extends to independent design guidance from SCI/BCSA, detailing the use of the Hollo-Bolt® as a primary connection. Lindapter applications include, connecting structural beams, roofing, cladding, flooring and temporary access runway beams as well as secondary steel installation.

Whether connecting to structural sections, hollow sections, concrete decking, purlins or light steel framing, Lindapter has the support connection to suit. Applications include the installation of pipe work, HVAC systems, sprinkler systems, electrical equipment and suspended ceilings.

Why Lindapter?

  • No Welding/ Site Drilling
  • Guaranteed Loads & Factor of Safety
  • No damage to protective coatings
  • Safe in hazardous environments
  • Adjustable On-Site

Types of Connections

  • Steel to Steel Connections
  • Steel Tube & Blind Connections
  • Steel Floor Connections
  • Pipe/Conduit Supports
  • Rail Clamps
View More
/Public/Images/product/a.jpg
Lindapter 'A' Recessed Clamp

Steelwork clamp with recessed top to hold the bolt head captive whilst the nut is tightened. The skirt prevents the clamp rotating during installation. Suitable for flanges up to 8°.


Material:
Malleable Iron

Finish:
Bright Zinc plated, Hot dip galvanized

 

More Info
---
Choose Options
View More
/Public/Images/product/lindapter_af.jpg
Lindapter 'AF' High Friction Clamp

High friction clamp with recessed top to hold bolt head captive while the nut is tightened. Can be combined with type CF. The skirt prevents the clamp rotating during installation. The tail of the AF spans across slotted holes. For flanges up to 10°.

Material:
SG iron

Finish:
Hot dip galvanized

More Info
---
Choose Options
View More
/Public/Images/product/lindapter_afcw.jpg
Lindapter 'AFCW' Clipped Washer for High Friction Clamp

Packing used to adjust the tail length of the clamp to meet differing beam flange thicknesses; has a slight bend along its center line which flattens out during installation.


Material:
Mild Steel

Finish:
Hot dip galvanized

More Info
---
Choose Options
View More
1189626449_type_af.jpg
Lindapter 'AFP1' Packing for High Friction Clamp P1

"AFP1" Packing for High Friction Clamp. Used to adjust the Lindapter clamps to meet different beam flange thicknesses. Type P1.
Electro-galvanized finish.

More Info
---
Choose Options
View More
/Public/Images/product/AFP.JPG
Lindapter 'AFP2' Packing for High Friction Clamp P2

Packing used to adjust the tail length of the AF High Friction clamps to meet differing beam flange thicknesses.

Material:
Mild steel

Finish:
Hot dip galvanized

More Info
---
Choose Options
View More
/Public/Images/product/afw.jpg
Lindapter 'AFW' Adapter Washer for High Friction Clamp

Adapter washer used to fill the recess of the type AF high Friction Clamp. Additionally it features two projections which, when the AFW is inverted, will captivate the larger hexagons of 10.9 bolts.(M12 – M20 only).

Material:
SG Iron, Malleable iron

Finish:
Hot dip galvanized

More Info
---
Choose Options
View More
/Public/Images/product/B.JPG
Lindapter 'B' Flat Top Clamp

Steel clamp with flat top which allows the bolt head or nut to be rotated. Suitable for use with all bolts, studs, tie rods and hook bolts and parallel flanges.

Material:
Malleable Iron

Finish:
Bright Zinc plated, Hot dip galvanized

More Info
---
Choose Options
View More
/Public/Images/product/br.jpg
Lindapter 'BR' Flat Top Clamp

Versatile clamp for steel beams or rails. The skirt prevents the clamp from rotating during installation. The BR tail spans slotted holes. Suitable for flanges up to 8°.

Material:
Malleable Iron

Finish:
Bright Zinc plated, Hot dip galvanized

More Info
---
Choose Options
View More
/Public/Images/product/cw.jpg
Lindapter 'CW' Clipped Washer

"CW" Clipped Washer is a packing used with Types A, AH, B and BR to adjust the tail length of the clamp to meet differing beam flange thicknesses. The Type CW fits on the bolt between the clamp and the location plate.

Material:
Mild Steel

Finish:
Bright Zinc Plated, Hot dip galvanized .

More Info
---
Choose Options
View More
/Public/Images/product/d2.jpg
Lindapter 'D2' Recessed Adjustable Tail Clamp

Adjustable clamp incorporating a setscrew tail to accommodate a wide range of flange thicknesses. The type D2 has a recessed head to hold the bolt head captive. The skirt prevents the clamp rotating during installation. Suitable for flanges up to 5°.

Material:
Malleable Iron

Finish:
Bright Zinc plated, Hot dip galvanized

More Info
---
Choose Options
View More
/Public/Images/product/d3.jpg
Lindapter 'D3' Flat Top Adjustable Tail Clamp

Adjustable flat top clamp incorporating a setscrew to accommodate a wide range of flange thicknesses.
The skirt prevents the clamp rotating during installation. Suitable for flanges up to 5°.

Material:
Malleable Iron

Finish:
Bright Zinc plated, Hot dip galvanized

More Info
---
Choose Options
View More
/Public/Images/product/F3.JPG
Lindapter 'F3' Flange Clamp

A two part flange clamp with large clamping range. The bolt can be substituted with either threaded rod or hook bolts. For parallel flanges only.

Material:
Malleable iron

Finish:
Hot dip galvanized

More Info
---
Choose Options
View More
/Public/Images/product/F9.JPG
Lindapter 'F9' Flange Clamp

Flange Clamp for connecting all types of parallel running steel with flanges of the same width. Can be used with bolts or alternatively with threaded rod. Not suitable for tapered flanges.

Material:
Malleable Iron

Finish:
Bright Zinc plated, Hot dip galvanized

More Info
---
Choose Options
View More
/Public/Images/product/FC.JPG
Lindapter 'FC' Adjustable Flush Clamp

The Flush Clamp is a Girder Clamp System without the need of a location plate. Suitable for connecting beams of varying widths and thicknesses. Suitable for flanges up to 10° slope.

Material:
Forged Steel

Finish:
Bright Zinc plated plus JS500

More Info
$236.03
Buy
View More
/Public/Images/product/FF.JPG
Lindapter 'FF' Floorfast Clamp

The product consists of a malleable iron body casting with a countersunk socket screw. The eccentric stepped web of the casting allows it to lock under the steel, providing full face contact when torque is applied. For thicker flanges, packing pieces can be supplied. Lloyd's Register Type Approval covers clamping force and vibration.

Material:
Malleable iron, Stainless Steel Grade 316

Finish:
Bright zinc plated, Hot dip galvanized

More Info
---
Choose Options
View More
/Public/Images/product/FL.JPG
Lindapter 'FL' Flange Clamp

Clamp suitable for use with parallel or tapered flange beams, supplied with the back hole drilled or tapped. The type FL uses a grade 8.8 cup point setscrew for secure grip. Supplied with square head setscrews. Can be used with type SW – Swivel Unit when connecting to inclined sections.

Material:
Malleable iron

Finish:
Bright zinc plated

More Info
---
Choose Options
View More
/Public/Images/product/FL.JPG
Lindapter 'FL' Flange Clamp – Stainless Steel – Clear Bolt Hole

Type FL, in Stainless Steel with Clear Bolt Hole – Flange Clamp is a cost-effective method of suspending building services from steel beams. The clamp is suitable for use with parallel or tapered flange beams.

More Info
$19.13
Buy
View More
/Public/Images/product/fls.jpg
Lindapter 'FLS' Swivel Flange Clamp

Beam flange clamp with swivel unit. The Swivel Flange Clamp provides a quick and cost-effective method for suspending threaded rod from steel beams, and is suitable for use with either parallel or tapered flange beams. Supplied with grade 8.8 setscrew for secure grip.

Material:
High Grade Alloy Steel

Finish:
Bright zinc plated

More Info
$9.59
Buy
View More
/Public/Images/product/hollobolt.jpg
Lindapter 'HB' Hollo-Bolt

Suitable for hollow sections, tubes and where access is available from one side only. For corrosion protection, the Hollo-Bolt® comes with additional JS500 protection as standard or hot dip galvanized. Sizes 5/8" and 3/4" have a patented collapse mechanism for optimized clamping force. Speedy installation with standard tools. Awarded the Design Council’s Millennium Product status for innovation in the year 2000.

Material:
Stainless steel Grade 316

Finish:
Hot dip galvanized, Bright zinc plated plus JS 500

More Info
---
Choose Options
View More
Lindapter_HB_FlushFit.jpg
Lindapter 'HBFF' Hollo-Bolt Flush Fit

The Flush Fit Hollo-Bolt merges the technical advantages of the distinguished Hollo-Bolt with the aesthetic benefits of a discreet connection and is suitable for hollow sections or conventional steel where access is available from one side only.

The latest Hollo-Bolt creates immense opportunity for architectural design as the bolt is concealed within the steel with no protruding bolt head or collar.

Installation is fast and simple using Lindapter’s innovative installation nut (included) allowing the Flush Fit to be installed without the requirement of specialist skills or equipment.

Material:
Mild Steel, Stainless Steel Grade 316.

Finish:
Bright zinc plated plus JS 500

More Info
---
Choose Options
View More
/Public/Images/product/hc.jpg
Lindapter 'HC' Hemispherical Cup

For vertical suspension on angled surface of up to 10° swing either side of the vertical. The hemispherical washer (HW) can be used without the cup. Loads are subject to applications, please contact Lindapter.

Material:
Malleable Iron

Finish:
Bright Zinc plated, Hot dip galvanized

More Info
---
Choose Options
View More
/Public/Images/product/HD.JPG
Lindapter 'HD' Clip

The rail clamps Type Lindapter HD facilitate precise alignment of the rails by allowing a high degree of stepless lateral adjustability. Technical Data - Suitable for all rails with tapered flanges and crane speeds of up to 60m/min. For wheel loads above 400kN or lateral loads higher than wheel loads please contact Lindapter.

Material:
Malleable iron, SG iron

Finish:
Corrosion protection as requested

More Info
---
Choose Options
View More
/Public/Images/product/HC.JPG
Lindapter 'HW' Hemispherical Washer

For vertical suspension on angled surface of up to 10° swing either side of the vertical. The hemispherical washer (HW) can be used without the cup. Loads are subject to applications, please contact Lindapter.

Material:
Malleable Iron

Finish:
Bright Zinc plated, Hot dip galvanized

More Info
---
Choose Options
View More
/Public/Images/product/lindibolt.jpg
Lindapter 'LB2' Lindibolt 2

Self heading bolt suitable for connecting to hollow-sections, tubes and where access is available from one side only. The Lindibolt® uses a standard clearance hole.

Material:
Mild Steel, Stainless steel grade 316

Finish:
Bright zinc plated

More Info
---
Choose Options
View More
/Public/Images/product/LC.JPG
Lindapter 'LC' Lindiclip (1/4” or M6)

Beam clamp with tapped holes in the back face and lower jaw to accept threaded rod or cable clips. Comes assembled with a grade 8.8 case-hardened cup point setscrew and locknut. For parallel or tapered flanges.

Material:
Malleable iron

Finish:
Bright zinc plated

More Info
---
Choose Options
View More
/Public/Images/product/LR.JPG
Lindapter 'LR' Self Adjusting Clamp

Self adjusting clamp for various flange thicknesses and slopes up to 15°. The leg of the saddle prevents the clamp from rotating during installation. The LR tail spans slotted holes.

Material:
Malleable Iron

Finish:
Bright Zinc plated, Hot dip galvanized

More Info
---
Choose Options
View More
/Public/Images/product/P1S.JPG
Lindapter 'P1' and 'P2' Short Packings

Packings are used to adjust the Lindapter clamps to meet different flange thicknesses. Both products fit on the bolt
between the clamp and the location plate.

The Type P1 is thicker than the Type CW, and the Type P2 being twice the thickness of the P1.

The P1 and P2 short are used with Types A, AH, B and BR Lindapters.

Material:
Mild Steel, Malleable iron

Finish:
Bright zinc plated, Hot dip galvanized

More Info
---
Choose Options
View More
/Public/Images/product/P1.JPG
Lindapter 'P1' and 'P2' Long Packings

Packings are used to adjust the Lindapter clamps to meet different flange thicknesses. Both products fit on the bolt
between the clamp and the location plate.

The Type P1 is thicker than the Type CW, with the Type P2 being twice the thickness of the P1.

The P1 and P2 Long are for the use with the Types LR, D1 (not available,) D2 and D3 adjustable tail Lindapters where the flange thickness being clamped is greater than the maximum adjustable range.


Material:
Mild Steel, Malleable iron

Finish:
Bright zinc plated, Hot dip galvanized

More Info
---
Choose Options
View More
/Public/Images/product/T.JPG
Lindapter 'T' Tip

To fill the nose of type A and B, making it horizontal. For parallel flanges only. The thickness ‘T’ should be added for tail length and bolt length calculations. The product is for aesthetic purposes only and technically not necessary.

Material:
Malleable iron

Finish:
Bright zinc plated, Hot dip galvanized

More Info
---
Choose Options
View More
/Public/Images/product/tc.jpg
Lindapter 'TC' Toggle Clamp

The Toggle Clamp is designed for service suspension from pre-cast hollow core slabs (minimum depth of core 3") as well as HSS, steel sheeting or purlins.

Material:
Steel Strip

Finish:
Bright zinc plated

More Info
---
Choose Options
View More
/Public/Images/product/W.JPG
Lindapter 'W' Deep Washer

Washer to fill the recess of type A to enable the nut to be tightened.

Material:
Mild Steel, Malleable iron

Finish:
Bright zinc plated, Hot dip galvanized

More Info
---
Choose Options